PLUMBING 101: A NECESSITY FOR BATHTUB INSTALLATION

Plumbing 101: A Necessity for Bathtub Installation

Plumbing 101: A Necessity for Bathtub Installation

Blog Article

Book With Us Today!

How do you feel in regards to How to Install a Bathtub?


Tools You Need to Install a New Bathtub
Setting up a tub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough project. If the old bathtub is easily obtainable, the job can relocate easily; if you have to open up a wall to get rid of the old tub and place the brand-new tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to move out the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Chances are you might require a specialist plumber to make tube links.
This short article will assist you install a new tub in your bathroom if you have already acquired a brand-new tub and also do not require to alter the plan of your previous water system pipes.
Your tools and material list need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome because of the limited accessibility that is often the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
    Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a link to the current supply pipes.
    If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in location between the faucet and also the sink. Protect the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap ports. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Installing the Tub


    Utilizing both wooden boards under its feet, put the bathtub in the required position. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little points.
    The following goal is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the bath tub until the spirit level reads level.
    To set up faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression join; then do the same for the various other faucet.
    Turn on the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
    Lastly, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the bathtub has actually been used at the very least when as this will resolve it into its last placement.

    Planning for the Installation


    To start with, the supporting framework provided with the bath should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
    Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final position.

    Tiling Around the Tub


    In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break an inflexible seal, causing the water to penetrate the wall between the bath and also the tiling, resulting in problems with moisture as well as feasible leaks to the ceiling listed below.
    You can select from a range of coloured sealers to assimilate your components and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the tub with water before sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture rather very early if you do not take into consideration this motion prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I'm just very taken with A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the entire piece. Make sure you set aside a second to distribute this blog entry if you liked it. I cherish reading our article about How to Install a Bathtub Yourself.


    Reliable help? Dial.

    Report this page